Allantoin: in which phase?
Doreen
Member
in Formulating
Today I was reading a document (of International Specialty Products) about allantoin.
I read that allantoin is amphoteric and anionic at basic conditions.
- Does that mean that it is dipolar at a neutral pH?
The supplier suggests to suspend it in emulsions in the cool down phase <50°C. According to them recrystallization can occur later when it has been solubilized >50°C.
I never suspend allantoin, I always dissolve it in the water phase ≥70°C and luckily I've never had recrystallization problems so far.
I read that the solubility in water is 0.45 g/100 g at 25°C, so I guess that if you mix well and let it be, 0.45% of the suspended particles will dissolve later on anyway at room temperature?
A prototype formula was attached: 1% allantoin suspended in an anhydrous, lipophilic body balm.
- Does that actually work, suspending a water soluble, fine powder like allantoin in a lipophilic base?
- Are there other reasons than crystallization alone, to suspend allantoin in the cool down phase?
I read that allantoin is amphoteric and anionic at basic conditions.
- Does that mean that it is dipolar at a neutral pH?
The supplier suggests to suspend it in emulsions in the cool down phase <50°C. According to them recrystallization can occur later when it has been solubilized >50°C.
I never suspend allantoin, I always dissolve it in the water phase ≥70°C and luckily I've never had recrystallization problems so far.
I read that the solubility in water is 0.45 g/100 g at 25°C, so I guess that if you mix well and let it be, 0.45% of the suspended particles will dissolve later on anyway at room temperature?
A prototype formula was attached: 1% allantoin suspended in an anhydrous, lipophilic body balm.
- Does that actually work, suspending a water soluble, fine powder like allantoin in a lipophilic base?
- Are there other reasons than crystallization alone, to suspend allantoin in the cool down phase?
Tagged:
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Quick Links
Latest Q&A session
Forum Instructions
Categories
In this Discussion
Comments
May I ask you what phase you would suggest? Thanks a lot in advance!
I'v got answers on my questions above and would like to share it, hopefully it might be of help for you too.
About suspending allantoin to a lipophilic product: this is probably useful indeed. Apparently it doesn't need to be in a dissolved state per se for it's soothing properties. I have attached the document with the lipophilic treatment stick with 1% allantoin formula (on page three).
Here is the answer I got:
"Allantoin is an amphoteric molecule. It can have a positive charge under acidic conditions, but could only have a negative charge under very basic conditions. Betaine on the other hand can only have a positive charge under very acidic conditions, and it's usually present as a zwitterion (both anionic and cationic charges at the same time, with a net carge of zero). It could never be anionic since it has a permanent positive charge. At the pH of 5.32, allantoin is cationic, so it might actually interact with the anionic emulsifier. You basically suspend allantoin due to its low solubility and recrystallization risk. Incorporation into an emulsion during the cool down phase is done in the same way as you do with many other ingredients, only that you need vigorous mixing."
So the minor pilling issues I had recently, could indeed be due to the allantoin interacting with the glyceryl stearate citrate.
You're welcome! :-)
No problem! :-) I've also had a few times that my name was tagged, but I didn't get a notification.
Glad to see you also don't put it in the cool down! I've never had problems with allantoin either, well up to now maybe (the 'gritty deodorant' discussion). But maybe that was due to a too fast cool down.